24C04 ATMEL PDF

24C02/24C Two-Wire Serial EEPROM. Preliminary datasheet. 2K ( X 8)/ 4K ( X 8). 1/ MRD. Features. ▫. Low-voltage and Standard-voltage. Find great deals for 10pcs AT24C04 24c04 Serial EEPROM Sop-8 Atmel. Shop with confidence on eBay!. Read about ’24C04 Interfacing issue’ on elementcom. Hey there,I am trying to interface the AT24C04 4K EEPROM with Atmega

Author: Nebar Kagarisar
Country: Botswana
Language: English (Spanish)
Genre: Automotive
Published (Last): 11 March 2011
Pages: 139
PDF File Size: 15.37 Mb
ePub File Size: 17.85 Mb
ISBN: 941-1-74751-645-2
Downloads: 27894
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuk

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. However, it doesn’t matter what I set these pins to. This output is from I2C scanner. Is there something else I need to do? Are you being confused by the common mistake that many people make where they treat the address of an I 2 C wrongly?

Even the data sheet that you linked can lead to confusion in this regard.

24C04 and Arduino

In figure 4 they refer to the address as an 8-bit quantity:. Also be aware that the A0 to A2 pins on the device package are meant to remain static in a design.

If a total of eight 24C02’s are used in the design then each of the devices will have these three pins hard strapped in a different combination from the set of b, b, b, b, b, b, b and b. When you say that you are “writing” to the pins this does not make clear exactly what you are doing. Normally there is no writing to the 24C02 pins. Instead the three bits that you supply out on the interface in the atmwl address field must match the hard strapped values on the pins in order for the device to be selected.

  AHMAD IBN RUSTAH PDF

10pcs AT24C04 24c04 Serial EEPROM Sop-8 Atmel

On top of that I have never been sure that it is even possible to dynamically change the strapped value on the A0, A1 and A2 pins of a 24C02 after it has powered up. A2 are used for creating the address.

2c04 device will not respond to the address that is being set dynamically. It considers the value of the A0,A1 and A2 before the power up and sticks to it till reset.

By clicking “Post Your Answer”, you acknowledge that you have read our 224c04 terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. Home Questions Tags Users Unanswered.

Found 8 device s. Check your chips markings. You do not write the addresses; you hardwire them. TurboJ The chip says the following: Can you explain what hardwiring is? In figure 4 they refer to the address as an 8-bit quantity: In Arduino, the function that does this is digitalWrite. That’s why I said “write”. If you just have one 24C02 then you would connect all three of those pins to GND as b. Then when you want to write to the part use an address byte of atkel and when you want to read use an address byte of 0xA1.

  BARBARIANS OF LEMURIA RPG PDF

Then the address byte that you use to write to the second chip would be 0xA2 and the address byte for reading the second chip would be 0xA3. Then the address byte that you use to write to the third chip would be 0xA4 and the address byte for reading the second chip would be 0xA5.

Can’t change the values dynamically. It will answer to address that was set up before powering up.

So for example you keep A0: MaNyYaCk 6 Can you give more information? But my suggestion would to directly connect them to ground or VCC for the addressing scheme. Maybe the issue is setting the address after power on.

10pcs At24c04 24c04 Serial EEPROM Sop-8 ATMEL

I will try in about an hour. Sign up or log in Sign up using Google.

Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Qtmel, but never shown. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.