ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||2 October 2011|
|PDF File Size:||4.17 Mb|
|ePub File Size:||4.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Originally approved in Permission rights to photocopy the standard may also be secured from the ASTM website www. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.
One bend test shall be made from one end of each coil. Types and L are weldable by most fusion or resistance welding techniques. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Last previous edition approved in as A — Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides.
A number in parentheses indicates the year of last reapproval. Only annealed conditions of grades speci? Material Test Report and Certi?
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Find out what NKS can do for you. Number of Tests 8. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.
This revision of Speci? The noncontrolling factor normally will exceed considerably the speci?
Rockwell B 95 95 Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. If filler metal is required, Type is normally used.
304 and 304L Stainless Steel
These alloys represent an excellent combination of corrosion resistance and fabricability. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
HardC Elongation asrm 2 in. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? HRC typical L Ann 25 min.
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Type L LN B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? However, in the case of dispute, tests shall be made by pressure. Annealed Types and L qstm be fabricated by roll forming, deep drawing, bending and most other fabrication techniques.
The values given in parentheses are for information only.
and L Stainless Steel – NKS
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
Types and L cannot be hardened by thermal treatment. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: D PSS means plate, strip, sheet.
Maximum unless otherwise indicated. This standard has been approved for use by agencies of the Department of Defense. Hard Elongation in 2 in.
A — 10 Standard Speci?