HT12E ENCODER DATASHEET PDF

HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Samukasa Zololabar
Country: Burma
Language: English (Spanish)
Genre: History
Published (Last): 10 March 2018
Pages: 471
PDF File Size: 20.9 Mb
ePub File Size: 4.30 Mb
ISBN: 643-6-51646-316-9
Downloads: 79130
Price: Free* [*Free Regsitration Required]
Uploader: Bakree

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

HT12E Datasheet

These 12 bits are divided into 8 address bits and 4 data bits. Pull the Transmission Enable pin pin 14 to ground to activate transmission. If you want security you can connect any of the 8 pins to 5V to make it high.

The IC is has a wide range of operating voltage from 2. These four pins are used to send data, the data encoded here will be decoded h1t2e HT12D IC sharing the same address bits. Choosing Motor For Robots. This pin dataaheet to be connected to Ground 0V to enable the Transmission. Virgin Galactic datasueet Commercial Space Flight. SPI Module of Arduino. Choosing Battery for Robots.

They can also be connected to switches to manually send and receive data. What is Web Browser.

  FUSARO MI NOVIA PDF

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

Simply put, HT12E converts the parallel inputs into serial output. Skip to main content. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. The primary function of HT12E is encodef encode a bit and send it out through the output pin.

HT12E Encoder IC

Connected to the Ground of circuit. These two ICs together form an Encoder and Decoder pair. It is mainly used in interfacing RF and infrared circuits. This oscillator can be used by connecting these two pins through a 1M Resistor. The IC has a built in oscillator. As soon as TE returns to high, the encoder output completes its final cycle and then stops.

The Encoded 12 bit output data can be obtained from this pin. It encodes encodre 12 bit parallel data into serial for transmission through an RF transmitter. Interface SD Card with Arduino. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

It is very important that your Decoder should also have this same address for them to talk to each other. TL — Programmable Reference Voltage.

  HOOPER HUMPERDINK PDF

Enxoder are paired with 2 12 series of decoders for use in remote control system applications. HT12E is an encoder integrated circuit of 2 12 series of encoders. HT12E has a transmission enable pin which is active low. Arduino based GPS receiver.

Supply voltage; 5V 2. These are the 8-bit address bits, which is used to protect your data. Transmission enable; active low. Can range from 2. The encoded bit can be obtained from the Dout pin pin You can know to set up the HT12D after this from here. This high-density System-in-Package SiP integrates controller, power switches, and support components.

In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. We should set the bits in same pattern on Encoder and Decoder IC to pair them.

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. Submitted by admin on 30 October Interface GPS with Arduino. This cycle is repeated as long as TE is kept low.